公司信息及水印
牌号简介 About |
---|
该产品由热塑性弹性体皮层压到封闭单元,交联聚烯烃泡沫,然后层压到我们的tuff-X刚性基板。低光泽和柔软的手感,消除了对软触摸涂料的需求。(成型后小于5%)它也有助于消除止血药特有的吱吱声和嘎吱声。在不损失性能的情况下,可回收未上漆的废料。应用:TUFF-X STF是理想的内部和外部部件,包括中控台、仪表板、门板和许多其他部件。这满足了客户对低光泽、柔软触感材料的需求,以软化农业设备、船舶、重型卡车、房车和其他市场中的内外部应用,同时使用热塑性可回收材料。加工:Prime Tuff-X STF可采用标准成型设备成型。泡沫/皮肤侧不应形成在工具上。辐射热效果最好,首选区域控制陶瓷或石英加热器。跳动或凸缘区域应大于腹肌或臀部的尺寸。基材应达到正常的成形温度,但泡沫不应超过310°F。整理:TUFF-X STF可以用钢制规则或硬模具制造,加热的刀具或工具也可以工作,但是不推荐布线和锯切。机械螺钉和紧固件以及3M公司开发的一些粘合剂可用于粘合。请与Primex塑料公司代表联系,了解有关表面处理、制造或热成型工艺的更多信息。颜色、纹理和功能:Primex通常提供那不勒斯和皮革纹理,以及由浅色和深色、棕褐色和灰色组成的四种颜色。自定义颜色匹配可用,但订单尺寸必须经过批准。 This product consists of a Thermoplastic elastomer skin laminated to closed-cell, cross-linked polyolefin foam that is then laminated to our Tuff-X rigid substrate. Low gloss and soft feel eliminate the need for soft-touch paint. (<5% after forming) It also helps eliminate the squeak and rattle that is characteristic of Styrenics. Recycling of unpainted scrap is possible with no loss of properties. Applications: Tuff-X STF is ideal for interior and exterior components, including center consoles, instrument panels, door panels, and many others. This addresses the customers' desire for a low-gloss, soft feel material to soften interior and exterior applications in markets such as agricultural equipment, marine, heavy trucks, RV cabs, and others, while utilizing a thermoplastic, recyclable material. Processing: Prime Tuff-X STF can be formed using standard forming equipment. The foam/skin side should not be formed against the tool. Radiant heat works best, Zone controlled ceramic or quartz heaters are preferred. The run out or flange area should be greater than what is figured for ABS or HIPS. The substrate should reach normal forming temperature but the foam should not exceed 310°F. Finishing: Tuff-X STF can be fabricated by using steel rule or hard dies, heated knives or tooling will also work, however, routing and sawing is not recommended. Mechanical screws and fasteners, as well as some adhesives that have been developed by 3M, may be used for bonding. Please contact your Primex Plastics representative for more information on finishing, fabricating, or the thermoforming process. Colors, Textures and Capabilities: Primex typically offers a Naples and Leather texture and four colors consisting of light and dark, tan and gray. Custom color matching is available but order sizes must be approved. |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
0.731 | g/cm³ | ISO 1183 |
收缩率 Shrinkage rate |
0.70 到 0.90 | % | ISO 294-4 |
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
装有测量仪表的落镖冲击 Dart impact equipped with measuring instruments |
ASTM D3763 | ||
-15℃,Total Energy -15℃,Total Energy 3 |
63.0 | J | ASTM D3763 |
23℃,Total Energy 23℃,Total Energy |
52.0 | J | ASTM D3763 |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
热变形温度 Hot deformation temperature 4 |
|||
0.45 MPa,未退火 0.45 MPa, unannealed |
116 | ℃ | ISO 75-2/B |
1.8 MPa,未退火 1.8 MPa, unannealed |
℃ | ISO 75-2/A | |
线性热膨胀系数 Linear coefficient of thermal expansion |
|||
MD MD |
1/℃ | ||
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
邵氏硬度 Shore hardness 2 |
|||
邵氏 A Shaw's A 2 |
ISO 868 | ||
拉伸强度 tensile strength |
|||
屈服 yield |
MPa | ISO 527-2 | |
弯曲模量 Bending modulus |
MPa | ISO 178 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
2 50% ductile |
3 Skin |
4 Substrate |
【新闻资讯】查看全部
库存减少 成本高企——来自东北春耕市场的调查
2022-03-26 近日,一则预估春耕东北肥料缺口最少超过30%,春耕用肥保供堪忧的消息在网上传得沸沸扬扬。作为中国最大的粮仓,东北春耕化肥稳价保供是每年的头等大事。在该地区疫情多点散发 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |