公司信息及水印
牌号简介 About |
---|
模克隆紫外线板是一种透明的聚碳酸酯产品,采用先进的抗紫外线技术,确保在平玻璃和曲面玻璃应用中具有持久的户外耐候性能。它比丙烯酸和玻璃具有更高的抗冲击性,安装时可冷弯成型。模克隆紫外线是生产具有高光学质量和最小的失真清晰,一系列标准的建筑色彩,或可定制匹配任何颜色。模克隆紫外线有一个十(10)年的产品保修期,针对破损,发黄和光传输损失。保修条款可根据要求提供。适用于雨篷、入口天篷、天窗、桶形拱顶、上釉拱门、有盖人行道以及倾斜、垂直和弯曲的玻璃。 Makrolon® UV sheet is a transparent polycarbonate product with an advanced UV resistance technology that assures long lasting outdoor weathering performance in flat and curved glazing applications. It has higher impact resistance than acrylic and glass, and it can be cold-formed during installation. Makrolon UV is produced with high optical quality and minimal distortion in clear, a range of standard architectural tints, or can be custom matched to any color. Makrolon UV has a ten (10) year Limited Product Warranty against breakage, yellowing, and loss of light transmission. The terms of the warranty are available upon request. Applications Awnings, entryway canopies, skylights, barrel vaults, glazed archways, covered pedestrian walkways, and sloped, vertical, and curved glazing |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
1.20 | g/cm³ | ASTM D792 |
吸水率 Water absorption rate |
|||
24hr 24hr |
0.15 | % | ASTM D570 |
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
悬臂梁缺口冲击强度 Impact strength of cantilever beam notch |
|||
3.2mm 3.2mm |
850 | J/m | ASTM D256 |
悬臂梁无缺口冲击强度 Notched impact strength of cantilever beam |
|||
3.2 mm 3.2 mm |
无断裂 | ASTM D256 | |
装有测量仪表的落镖冲击 Dart impact equipped with measuring instruments |
|||
3.18 mm 3.18 mm |
> 63.7 | J | ASTM D3763 |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
热变形温度 Hot deformation temperature |
ASTM D648 | ||
0.45 MPa,未退火 0.45 MPa, unannealed |
℃ | ASTM D648 | |
1.8 MPa,未退火 1.8 MPa, unannealed |
℃ | ASTM D648 | |
脆化温度 Embrittlement temperature |
℃ | ASTM D746 | |
线性热膨胀系数 Linear coefficient of thermal expansion |
|||
MD MD |
1/℃ | ASTM D696 | |
导热系数 Thermal conductivity coefficient |
W/m/K | ASTM C177 | |
遮阳系数 Sunshade coefficient |
NFRC 100-2010 | ||
Clear:5.99 mm Clear:5.99 mm |
NFRC 100-2010 | ||
Gray or Bronze:5.99 mm Gray or Bronze:5.99 mm |
NFRC 100-2010 | ||
U Factor U Factor |
NFRC 100-2010 | ||
Summer:5.99 mm Summer:5.99 mm |
BTU/hr/ft²/°F | NFRC 100-2010 | |
Summer:9.53 mm Summer:9.53 mm |
BTU/hr/ft²/°F | NFRC 100-2010 | |
Winter:5.99 mm Winter:5.99 mm |
BTU/hr/ft²/°F | NFRC 100-2010 | |
Winter:9.53 mm Winter:9.53 mm |
BTU/hr/ft²/°F | NFRC 100-2010 | |
电气性能 Electrical performance |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
体积电阻率 Volume resistivity |
ohms·cm | ASTM D257 | |
介电强度 Dielectric strength |
|||
3.18 mm,在空气中 3.18 mm in air |
kV/mm | ASTM D149 | |
介电常数 Dielectric constant |
ASTM D150 | ||
10 Hz 10 Hz |
ASTM D150 | ||
60 Hz 60 Hz |
ASTM D150 | ||
耗散因数 Dissipation factor |
|||
60 Hz 60 Hz |
ASTM D150 | ||
耐电弧性 Arc resistance |
ASTM D495 | ||
-- -- 6 |
sec | ASTM D495 | |
-- -- 7 |
sec | ASTM D495 | |
阻燃性能 FLAME CHARACTERISTICS |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
Flash Ignition Temperature Flash Ignition Temperature |
℃ | ASTM D1929 | |
Horizontal Burn(AEB) Horizontal Burn(AEB) |
cm | ASTM D635 | |
自燃温度 Autoignition temperature |
℃ | ASTM D1929 | |
光学性能 optical performance |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
折射率 Refractive index |
ASTM D542 | ||
透光率 Transmittance |
ASTM D1003 | ||
3000 µm 3000 µm 8 |
% | ASTM D1003 | |
3000 µm 3000 µm 10 |
% | ASTM D1003 | |
3000 µm 3000 µm 11 |
% | ASTM D1003 | |
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
洛氏硬度 Rockwell hardness |
ASTM D785 | ||
M 级 M-level |
ASTM D785 | ||
R 级 R-level |
ASTM D785 | ||
拉伸模量 Tensile modulus |
MPa | ASTM D638 | |
拉伸强度 tensile strength |
ASTM D638 | ||
屈服 yield |
MPa | ASTM D638 | |
极限 limit |
MPa | ASTM D638 | |
拉伸应变 Tensile strain |
|||
断裂 fracture |
% | ASTM D638 | |
弯曲模量 Bending modulus |
MPa | ASTM D790 | |
弯曲强度 bending strength |
MPa | ASTM D790 | |
压缩模量 Compression modulus |
MPa | ASTM D695 | |
压缩强度 compressive strength |
MPa | ASTM D695 | |
剪切模量 shear modulus |
MPa | ASTM D732 | |
剪切强度 shear strength |
ASTM D732 | ||
-- -- 3 |
MPa | ASTM D732 | |
-- -- 4 |
MPa | ASTM D732 | |
泊松比 Poisson's ratio |
ASTM E132 | ||
耐磨耗性 Wear resistance 5 |
|||
Delta Haze Delta Haze 5 |
% | ASTM D1044 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
2 Yield |
3 Ultimate |
4 100 Cycles, CS-10F Wheel, 500 g load |
5 Tungsten Electrodes |
6 Steel Strip Electrode |
7 K09 Bronze |
8 I35 Dark Gray |
9 Clear |
10 I30 Gray |
【新闻资讯】查看全部
煤油共炼新工艺获突破
2021-09-13 搜料网资讯: 记者9月10日从陕西延长石油集团获悉,该集团牵头承担的科技部重点研发计划项目煤与重油共加氢及产品加工关键技术及示范装置连续运行通过考核。该项目通过完善工业 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |