![](/page/pc/images/result/icon-datasheet-right-ad-none.png)
![](/page/pc/images/result/downloads-img2.png)
公司信息及水印
![](/page/pc/images/result/downloads-img4.png)
![](/page/pc/images/result/downloads-img1.png)
![](/page/pc/images/result/downloads-tag3.png)
![](/page/pc/images/result/downloads-img1.png)
![](/page/pc/images/result/downloads-tag3.png)
![](/page/pc/images/result/downloads-img3.png)
牌号简介 About |
---|
这种双峰高分子量、高密度聚乙烯(HMW-HDPE)乙烯-己烯共聚物是为吹塑薄膜应用量身定制的,要求:良好的气泡稳定性和薄膜降深、高冲击强度和韧性、优异的刚度和拉伸强度平衡撕裂强度典型的吹塑薄膜应用包括:T恤袋Produce bags商品袋工业衬垫垃圾桶衬垫该树脂符合这些规范:FDA 21 CFR 177.1520(c)3.2a。该树脂可与表1、21 CFR 176.170(c)中定义的所有类型的食品接触,并在表2、21 CFR 176.170(c)中定义的使用条件b-h下使用。 |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
0.950 | g/cm³ | ASTM D1505 |
熔体质量流动速率 Melt Flow Rate |
|||
190℃,2.16kg 190℃,2.16kg |
0.060 | g/10min | |
190℃,21.6kg 190℃,21.6kg |
9.5 | g/10min | |
薄膜 film |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
薄膜厚度 film thickness 3 |
13 | µm | |
割线模量 Secant modulus |
|||
1% 正割,MD:13 µm,吹塑薄膜 1% secant, MD: 13 µ m, blow molded film |
827 | MPa | |
1% 正割,TD:13 µm,吹塑薄膜 1% secant, TD: 13 µ m, blow molded film |
MPa | ||
抗张强度 Tensile strength |
|||
MD:断裂,13 µm,吹塑薄膜 MD: fracture, 13 µ m, blow molded film |
MPa | ||
TD:断裂,13 µm,吹塑薄膜 TD: fracture, 13 µ m, blow molded film |
MPa | ||
拉伸应变 Tensile strain |
|||
MD,断裂,13 µm,吹塑薄膜 MD, fracture, 13 µ m, blow molded film |
% | ||
TD,断裂,13 µm,吹塑薄膜 TD, fracture, 13 µ m, blow molded film |
% | ||
落锤冲击 Drop hammer impact |
|||
13 µm,吹塑薄膜 13 µ m, blow molded film |
g | ASTM D1709 | |
埃尔曼多夫抗撕强度 Elmandorf tear strength |
|||
MD:13 µm,吹塑薄膜 MD: 13 µ m, blow molded film |
g | ||
TD:13 µm,吹塑薄膜 TD: 13 µ m, blow molded film |
g |
备注 |
---|
2、When blended with an approved black concentrate |
3、0.5 mil (12.7 micron) film produced using a grooved-feed extruder at a rate of 225 lb/h with a stalk height of 7 x Die Diameter, a 4:1 Blow-Up Ratio (BUR), a 6 inch die diameter and a 0.040 inch die gap. The nominal properties reported herein are representative of the product under these processing conditions, although film properties can vary depending on the specific film-blowing conditions. Therefore, the data should not be used for specification purposes. |
【新闻资讯】查看全部 ![]()
缺钱不是最大问题,博菱电器上市也走不出“代工”困境
2021-12-28 搜料网资讯: 曾于今年9月中止发行审核的博菱电器再次更新招股材料,日前已恢复发行审核。 博菱电器是一家以出口代工为主的厨房小家电生产商。去年疫情期间,受到人们居家隔离 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |