牌号简介 About |
---|
FX-8575是一种硬质聚氨酯配方的手工铸造方法。在不使用汞、MOCA或TDI的情况下,温和的后固化可获得良好的物理性能。此材料通过UL 94VO。 FX-8575 is a rigid polyurethane formulated hand casting methods. Excellent physical properties can be obtained with a mild post cure without the utilization of mercury, MOCA, or TDI. This material passes UL 94VO. |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
|||
Hardener Hardener |
1.10 | g/cm³ | |
固化处理 Curing treatment |
1.23 | g/cm³ | |
基体树脂 Matrix resin |
1.26 | g/cm³ | |
收缩率 Shrinkage rate |
|||
MD MD |
0.40 到 0.80 | % | ASTM D2566 |
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
弯曲模量 Bending modulus |
1930 | MPa | ASTM D790 |
弯曲强度 bending strength |
MPa | ASTM D790 | |
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
悬臂梁缺口冲击强度 Impact strength of cantilever beam notch |
J/m | ASTM D256 | |
阻燃性能 FLAME CHARACTERISTICS |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
阻燃等级 Flame retardant level |
UL 94 | ||
补充信息 Supplementary information |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
放热峰值 exothermic peak |
|||
200g mass 200g mass |
℃ | ||
Uncured Properties Uncured Properties |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
粘度 viscosity |
|||
25℃ 25℃ 2 |
Pa·s | ||
25℃ 25℃ 3 |
Pa·s | ||
25℃ 25℃ 4 |
Pa·s | ||
固化时间 Curing time 5 |
hr | ||
胶凝时间 Gelation time |
min | ||
Cured Properties Cured Properties |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
邵氏硬度 Shore hardness |
|||
邵氏 D Shaw's D |
ASTM D2240 | ||
拉伸模量 Tensile modulus |
MPa | ||
拉伸强度 tensile strength |
MPa | ASTM D638 | |
拉伸应变 Tensile strain |
|||
断裂 fracture |
% | ASTM D638 | |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
热变形温度 Hot deformation temperature |
|||
0.45 MPa,未退火 0.45 MPa, unannealed |
℃ | ASTM D648 | |
热固组件 Thermosetting components |
|||
树脂 resin |
|||
硬化法 Hardening method |
|||
脱模时间 stripping time |
|||
66℃ 66℃ |
min |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
2 Resin |
3 Mixed |
4 Hardener |
5 24 hours at 77°F + 1 hour at 150°F |
【新闻资讯】查看全部
生物3D打印市场预估 北美或成最大赢家
2016-03-09 近两年,3D打印技术的发展堪称飞速,2015年,全球3D打印市场值大约在110亿美元,预计2016年该数值将增长到267亿美元。在各项应用领域中,生物3D打印是最被人们看好的市场之一。 知名市场调研公司Acute Market Reports日前公布了一项报告,称生物3D打印市场将呈爆炸式速度发展,如果各项研究计划不出差错,整个器官移植医疗过程将被人造器官彻底改造。 生物3D打印技术的发展十分惊人,2014年生物3D打印市场值仅仅只有接近5亿美元,但在这两年 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |