| 牌号简介 About |
|---|
| SX级是热塑性注塑机和挤出机的高温清洗剂。SX级设计用于在高加工温度下保持热稳定性，同时促进材料和颜色的变化。它独特地适用于570°F以上的超工程树脂的吹扫。高温SX级是专门制定的，以保持高温加工温度下的热稳定性。净化过的烯基树脂：专门用于净化PPS、PEEK、LCP、Ultem等超级工程树脂。Victrex建议为Victrex PEEK聚合物使用清洁的高温级净化化合物。使用ASACLEAN™ SX等级：ASACLEAN™ SX进行吹扫的提示：由于可能发生分解，在温度高于700°F（370°C）的机器中，不应使其空转超过30分钟。始终保持桶内充满AsClean SX，以防止氧气进入桶内——过量的氧气会加速材料分解/碳形成，并可能在建议的温度范围的较高一端引发火灾。为了尽可能减少吹扫时产生过量烟雾的可能性，建议在机器附近放置一桶水。从喷嘴返回后，立即将清洁的吹扫桩放在水中。对于喷嘴悬挂或检查环清洁（碳和/或彩色沉积物），请联系您的技术销售代表以获取特别说明。如果加工温度达到或接近SX等级的最高推荐温度，建议使用低至中等背压和螺钉速度。用途：变色材料，高温树脂，加工温度：570-735°F（300-390°C）使用AsaClean时尖端：AsaClean不通过化学反应工作。有效清洗不需要任何浸泡时间或停留时间，为了获得最大的性能，ASACLEAN不应与其他材料一起稀释。ASACLEAN在最大搅拌下效果最好。使用最大安全螺杆速度和注塑成型也使用最大安全背压与螺杆在最前方的位置。 SX Grade is a high-temperature purging compound for thermoplastic injection molding and extrusion machines. SX Grade is designed to maintain thermal stability at high processing temperatures while facilitating material and color changes. It is uniquely suitable for purging super-engineering resins above 570°F. High Temperature SX Grade is specifically formulated to maintain thermal stability at high processing temperatures. Olefinic-Based Resins Purged: Exclusively used for purging super engineering resins such as PPS, PEEK, LCP, Ultem. VICTREX recommends ASACLEAN high temperature grade purging compound for VICTREX® PEEK™ polymers. Tips for purging with ASACLEAN SX Grade: ASACLEAN SX should not be left idle in the machine at temperatures above 700°F (370°C) for more than 30 minutes as decomposition may occur. Keep the barrel full of ASCLEAN SX at all times to prevent oxygen from entering the barrel -- excess oxygen will accelerate material decomposition/carbon formation and could potentially result in fire at the higher end of the recommended temperature range. To minimize the potential of excessive smoke while purging, it is recommended that a bucket of water be kept near the machine. Place ASACLEAN purge piles in water immediately after coming back from the nozzle. For nozzle hang-up or check ring cleaning (carbon and/or color deposits), please contact your technical sales representative for special instructions. If processing temperatures are at or near the maximum recommended temperature for the SX Grade, low to medium back pressure and screw speed are recommended . Applications: Color Changes Material Changes High Temperature Resins Processing temperature: 570 to 735°F (300 to 390°C) Tips when using ASACLEAN: ASACLEAN does not work by chemical reaction. No soak time or hold-up time is required for an effective purge For maximum performance, ASACLEAN should not be diluted with other materials. ASACLEAN works best with maximum agitation. Use the maximum safe screw speed and for injection molding also use maximum safe back pressure with the screw in the most forward position. |
产品描述 Product Description
用途：清洗复合物;
| 技术参数 Technical Data | |||
|---|---|---|---|
|
补充信息 Supplementary information |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
|
加工温度 Processing temperature |
299 到 391 | ℃ | |
| 备注 |
|---|
| 1 一般属性：这些不能被视为规格。 |
|
【新闻资讯】查看全部 
陶氏公司发布全新有机硅技术
2021-07-02 搜料网资讯： 6月30日，陶氏公司发布了三款全新应用于纯电动和混合动力汽车电子设备的有机硅产品：陶熙TC-2035 CV 粘接剂、陶熙TC-4551 CV 填缝剂和陶熙TC-4060 GB250 导热凝胶，其可控的挥 |
|
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任，并强烈建议在最终选择材料前，就数据值与材料供应商进行验证。 |
当前牌号已加入对比
支付宝
微信支付