牌号简介 About |
---|
Indothene LL LL 36RA045 UV 是以丁烯为共聚单体,气相流化床法生产的线性中密度聚乙烯。该等级通过适当数量的HAL进行稳定,以提供长期服务,无论是否混合任何炭黑,都能持续暴露在室外。Indothene LL LL 36RA045 UV 粉碎成20-30目粉末提供,加工性好。这一等级具有很好的环境应力抗裂性(ESCR)和硬度和冲击强度的结合。本品含有正常剂量的AO和高剂量的紫外线稳定剂。食品接触应用:该等级符合印度标准IS-10146-1982“与食品、药品和饮用水接触时安全使用的聚乙烯”的要求。它还符合IS:10141:1982中批准的成分积极列表。等级的抗氧化物含量小于3000 ppm。 Indothene-LL LL36RA045UV is a Linear Medium Density Polyethylene produced by gas phase fluidised bed process using butene as comonomer. This grade is stabilised with appropriate quantity of HALS to give a long service with continuos outdoor exposure with or without blending of any carbon black. Indothene-LL LL36RA045UV when pulverised into 20-30 mesh powder offers, good processability. This grade has very good Environmental Stress Crack Resistance (ESCR) and a combination of Hardness and Impact strength. This grade contains normal dose of AO and high dose of UV stabiliser. FOOD CONTACT APPLICATIONS : This grade meets the requirements of Indian Standard IS-10146-1982 on "Polyethylene for its safe use in contact with food stuffs, pharmaceuticals and drinking water". It also conforms to the positive list of constituents as approved in IS:10141:1982. The antioxidant content of the grade is <3000 ppm. |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
0.936 | g/cm³ | ASTM D1505 |
熔体质量流动速率 Melt Flow Rate |
|||
190℃,2.16kg 190℃,2.16kg |
4.5 | g/10min | ASTM D1238 |
抗环境应力开裂 ESCR(Environmental Stress Cracking Resistance) |
|||
10%非离子洗涤剂,F50 10% non-ionic detergent, F50 |
350 | hr | ASTM D1693 |
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
悬臂梁缺口冲击强度 Impact strength of cantilever beam notch |
|||
3.2mm,注塑成型 3.2mm, injection molded |
250 | J/m | ASTM D256 |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
维卡软化温度 Vicat Softening Temp |
117 | ℃ | ASTM D1525 |
熔融温度 Melting temperature |
℃ | ||
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
邵氏硬度 Shore hardness |
|||
邵氏 D Shaw's D |
ASTM D2240 | ||
拉伸强度 tensile strength |
|||
屈服,2 mm,模压成型 Yield, 2 mm, molded |
MPa | ASTM D638 | |
拉伸应变 Tensile strain |
|||
屈服 yield |
% | ASTM D638 | |
弯曲模量 Bending modulus |
|||
3.20 mm,模压成型 3.20 mm, molded |
MPa | ASTM D790 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
【新闻资讯】查看全部
全球30多个国度地域发行塑料钞票 中国暂无时间表
2017-03-09 “虽然我国目前暂时没有全面发行塑料钞票,但可以说,我国在塑料钞票研发领域的能力是十分超前的。”“对于我国塑料钞票的研究,央行已有专门部门在做,但何时全面发行暂无时间表。”中国人民银行两位副行长易纲和潘功胜近日在两会上透露的信息,让人们开始想象“另一种钞票”的可能性。 目前,全球已有英国、加拿大等30多个国家和地区发行塑料钞票,其中澳大利亚、新加坡等国的流通货币已经全部由纸币更换为塑料钞票。 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |