![](/page/pc/images/result/icon-datasheet-right-ad-none.png)
![](/page/pc/images/result/icon-datasheet-right-ad-none.png)
![](/page/pc/images/result/downloads-img2.png)
公司信息及水印
![](/page/pc/images/result/downloads-img4.png)
![](/page/pc/images/result/downloads-img1.png)
![](/page/pc/images/result/downloads-tag3.png)
![](/page/pc/images/result/downloads-img1.png)
![](/page/pc/images/result/downloads-tag3.png)
![](/page/pc/images/result/downloads-img3.png)
牌号简介 About |
---|
Shin Etsu Keg2000-60是一种快速固化型液体注射成型硅胶。它作为两种成分提供,以1:1的比例混合,以确保轻松和准确的混合。KEG2000-60的粘度很低,可以很容易地泵送到大多数注塑系统中。高温下高撕裂强度快速固化时间室温下长使用寿命典型应用O形圈隔膜盖橡胶辊连接器包装其他电气零件六级认证 Shin-Etsu KEG2000-60 is a fast cure type liquid injection molding silicone. It is supplied as two components which are mixed in a 1:1 ratio to ensure easy and accurate blending. The viscosity of KEG2000-60 is low enough to allow easy pumping through most injection molding systems. High tear strength Rapid cure time at elevated temperature Long pot life at room temperature Typical Applications O-Rings Diaphragms Capping Rubber Rollers Connector packaging Other electrical parts ClassVI certification |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
1.13 | g/cm³ | |
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
邵氏硬度 Shore hardness |
58 | ||
弹性体 Elastomer |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
拉伸强度 tensile strength |
10.5 | MPa | |
100% 应变 100% strain |
2.46 | MPa | |
拉伸应变 Tensile strain |
|||
断裂 fracture |
470 | % | |
撕裂强度 tear strength 2 |
kN/m | ||
压缩形变 Compression deformation |
|||
180℃,22 hr 180℃,22 hr |
% | ||
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
贮藏期限 Storage period |
|||
32℃ 32℃ |
wk | ||
后固化时间 Post curing time |
|||
200℃ 200℃ |
hr | ||
Uncured Properties Uncured Properties |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
固化时间 Curing time |
hr |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
2 B 模具 |
【新闻资讯】查看全部
添加色母后注塑成型罕见成绩
2017-05-22 “在阳光照射下,制品中有条纹状的颜料带”这个问题需从塑料物理机械性能和塑料成型工艺两个方面考虑: 1.注塑设备的温度没有控制好,色母进入混炼腔后不能与树脂充分混合。 2.注塑机没有加一定的背压,螺杆的混炼效果不好。 3.色母的分散性不好或树脂塑化不好。“工艺方面可作如下调试: (1).将混炼腔靠落料口部分的温度稍加提高 (2).给注塑机施加一定背压。 如经以上调试仍不见好,则可能是色母、树脂的分 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |