公司信息及水印
牌号简介 About |
---|
彩色护套/各种电信和工业应用 UNIGARD™ RE DFDA-1638 Natural is a non-halogen, flame retardant, thermoplastic, low smoke, low corrosive, and low toxic compound. It has been designed for general purpose, medium and low voltage applications. If needed, standard color concentrates (EVA or PE based) can be used. Used as jacket, it is designed to pass the IEC-332-3, the IEEE-383/UL-1685 vertical tray cable burn tests. Cable construction, of course, plays an important role in flame performance. DFDA-1638 Natural can be used as jacket for 90°C rated cables. DFDA-1638 Natural is also designed to maximize processing and flame performance. This compound can sustain extrusion temperatures up to 362°F (200°C) and can be extruded in typical single-flight metering PE screws, barrier screws, Maddock screws, and screws with mixing pins. Features UNIGARD RE DFDA-1638 Natural provides the following features: Highly flame retardant (VW-1, IEC-332-3, IEEE 383 flame test ratings) Environmentally friendly (lead-free, halogen-free, sulfur/antimony-free) Low smoke, low corrosivity, and low toxicity UV stabilized Contains copper inhibitor Ease of extrusion and no special screw required Good electrical properties, moisture resistance, and fluid resistance Good balance of toughness and flexibility Excellent cut-through, crush, and abrasion resistance Colorable for insulation and jacket applications |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
1.50 | g/cm³ | ASTM D1505 |
机械吸水率 Mechanical water absorption rate |
|||
70℃,7days 70℃,7days |
9.50 | mg/in² | UL 1581 |
抗环境应力开裂 ESCR(Environmental Stress Cracking Resistance) 2 |
|||
10%非离子洗涤剂 10% non-ionic detergent 2 |
720 | hr | ASTM D1693 |
弹性体 elastic body |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
撕裂强度 tear strength |
6.13 | kN/m | ASTM D470 |
老化性能 Aging performance |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
拉伸强度保持率 Tensile strength retention rate 3 |
|||
10 days,110℃ 10 days,110℃ 3 |
110 | % | ASTM D638 |
伸长保持率 Elongation retention rate 3 |
|||
10 days,110℃ 10 days,110℃ 3 |
% | ASTM D638 | |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
脆化温度 Embrittlement temperature |
℃ | ASTM D746 | |
热变形 thermal deformation 4 |
UL 1581 | ||
90℃ 90℃ |
% | UL 1581 | |
100℃ 100℃ |
% | UL 1581 | |
121℃ 121℃ |
% | UL 1581 | |
氧感应时间 Oxygen sensing time |
|||
Al pans,no crimping,no screen,100 ml oxygen/min Al pans,no crimping,no screen,100 ml oxygen/min |
min | ASTM D3895 | |
电气性能 Electrical performance |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
体积电阻率 Volume resistivity |
|||
23℃ 23℃ |
ohms·cm | ASTM D257 | |
介电常数 Dielectric constant |
ASTM D150 | ||
60 Hz 60 Hz |
ASTM D150 | ||
100 kHz 100 kHz |
ASTM D150 | ||
1 MHz 1 MHz |
ASTM D150 | ||
6 MHz 6 MHz |
ASTM D150 | ||
耗散因数 Dissipation factor |
ASTM D150 | ||
60 Hz 60 Hz |
ASTM D150 | ||
100 kHz 100 kHz |
ASTM D150 | ||
1 MHz 1 MHz |
ASTM D150 | ||
6 MHz 6 MHz |
ASTM D150 | ||
阻燃性能 FLAME CHARACTERISTICS |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
极限氧指数 Extreme oxygen index |
% | ASTM D2863 | |
酸性气体试验 Acid gas test |
|||
Generation Generation |
% | MIL C-24643 | |
毒性 toxicity |
NES 713 | ||
酸性气体排放 pH Acid gas emission pH |
IEC 754-2 | ||
酸性气体排放传导性 Conductivity of acidic gas emissions |
IEC 754-2 | ||
温度指数(燃烧) - Critical Temperature index (combustion) - Critical |
℃ | NES 715 | |
烟雾 smoke |
|||
2.54 mm 2.54 mm |
NES 711 | ||
烟雾密度 Smoke density |
ASTM E662 | ||
Flaming Mode - D1.5:2.54 mm Flaming Mode - D1.5:2.54 mm |
ASTM E662 | ||
Flaming Mode - D4.0:2.54 mm Flaming Mode - D4.0:2.54 mm |
ASTM E662 | ||
Flaming Mode - Dm,(corr.):2.54 mm Flaming Mode - Dm,(corr.):2.54 mm |
ASTM E662 | ||
非燃烧模式 - D1.5:2.54 mm Non combustion mode - D1.5:2.54 mm |
ASTM E662 | ||
非燃烧模式 - D4.0:2.54 mm Non combustion mode - D4.0: 2.54 mm |
ASTM E662 | ||
非燃烧模式 - Dm,(corr.):2.54 mm Non combustion mode - Dm, (cor.): 2.54 mm |
ASTM E662 | ||
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
邵氏硬度 Shore hardness |
|||
邵氏 A Shaw's A |
ASTM D2240 | ||
拉伸强度 tensile strength 3 |
MPa | ASTM D638 | |
拉伸应变 Tensile strain 3 |
|||
断裂 fracture 3 |
% | ASTM D638 | |
弯曲模量 Bending modulus |
|||
1% 正割 1% secant |
MPa | ASTM D790 | |
耐磨耗性 Wear resistance |
|||
1000 cycle 1000 cycle |
% | ASTM D1044 | |
Shrinkback(4 hrs,100℃) Shrinkback(4 hrs,100℃) 4 |
% | REA 89 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
2 No Cracks |
3 #14 AWG (1.63 mm dia.) solid copper conductor with 0.030 in (0.76 mm) insulation. |
4 #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. |
【新闻资讯】查看全部
原材料涨价层层传导 上市公司“见招拆招”沉着应对
2022-04-06 新能源汽车原材料价格的上涨正由上而下引发一系列连锁反应,困扰着整个行业的参与者。动力电池企业迫于成本压力,不得已改变价格谈判规则,按季度定价;整车厂商一边忙着与动 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |