牌号简介 About |
---|
Aquivion® PW79S基于四氟乙烯与磺酰氟化物乙烯基醚(sfve)cf2=cf-o-(cf2)2-so2f的短侧链共聚物的粗酸性粉末。生成的全氟聚合物的官能团是以磺酸形式存在的,SO3H。Aquivion® PW79S是化学稳定的(用S后缀表示)。Aquivion® PW79S的特点是等效重量低,离子交换能力强。在常规交换树脂耐化学性不足的情况下,也可以使用。由于它具有许多活性基团的超强酸功能,因此可以直接使用,也可以作为复合结构的一种成分,作为一种多相催化剂。这包括广泛的有机合成和各自的反应机制。它不溶于水、酸或碱以及大多数溶剂,除非使用极端条件。此外,Aquivion® PW79S还可以在某些有机溶剂中溶解,产生离子交换膜。合适的有机溶剂为偶极非质子,如N-乙基-2-吡咯烷酮(NEP)和二甲基亚砜。为了便于溶解,请将温度稍微升高到50-60°C。有关更多信息,请访问aquivion.com。 Aquivion® PW79S coarse, acid powder based on the short-side-chain (SSC) copolymer of Tetrafluoroethylene and the Sulfonyl Fluoride Vinyl Ether (SFVE) CF2=CF-O-(CF2)2-SO2F produced by Solvay. The resulting perfluoropolymer's functional groups are in their sulfonic acid form, SO3H. Aquivion® PW79S is chemically-stabilized (denoted by the S-suffix). Aquivion® PW79S is characterized by a low equivalent weight and a high ionic exchange capacity. It can be used as is under conditions where conventional exchange resins have shown insufficient chemical resistance. Due to its superacid functionality with many active groups, it can be used either directly or as an ingredient of composite structures active as a heterogeneous catalyst. This encompasses a wide range of organic syntheses and respective reaction mechanisms. It is insoluble in water, acid or bases and in most solvents unless extreme conditions are applied. Furthermore Aquivion® PW79S can be dissolved in some organic solvents to produce ion exchage capacity membrane. Proper organic solvents are dipolar aprotic such as N-ethyl-2-pyrrolidone (NEP) and dimethyl sulfoxide. To facilitate the dissolution, slightly increase the temperature to 50-60°C. Please visit Aquivion.com for more information. |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
当量 equivalent 2 |
|||
EW EW 2 |
770 到 810 | g/eq | 内部方法 |
含水量 water content |
5.0 | % | |
总酸量 Total acidity |
1.23 到 1.30 | meq/g | 内部方法 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
2 eq = mol SO3H |
【新闻资讯】查看全部
注塑制品毛刺过大缘由剖析
2017-12-28 毛刺过大多发生在分合面上,即动模与静模之间、滑块的滑配部位、镶件的缝隙、顶杆孔隙等处流入熔料,在制件上形成多余的飞边毛刺。 这样的飞边毛边毛刺,在成型时起杠杆作用、会使飞边毛刺进一步增大,从而造成模具局部的凹陷,形成时飞边毛刺进一增大的恶性循环。所以,如果一开始发现产生了飞边毛刺,就必须尽早修整模具。 毛刺的产生有下面几种原因 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |