牌号简介 About |
---|
LLD929P是专门为中型和大型水箱设计的复合旋转成型材料。提供不同的定制颜色,紫外线水平从8-20,可选功能,如防尘,防霉,抗菌。 LLD929P is special designed compounded rotomolding material for middle size and large size water tank. Provide different customized colors, UV level from 8-20, optional functions such as dust proof, mildew proof and antibacterial. |
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
0.936 | g/cm³ | ISO 1183 |
表观密度 Apparent density |
0.37 | g/cm³ | ISO 60 |
熔体质量流动速率 Melt Flow Rate |
|||
190℃,2.16kg 190℃,2.16kg |
5.0 | g/10min | ISO 1133 |
抗环境应力开裂 ESCR(Environmental Stress Cracking Resistance) |
1000 | hr | ASTM D1693 |
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
悬臂梁冲击强度 Izod notched impact strength |
230 | J/cm | ARM |
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
热变形温度 Hot deformation temperature |
|||
0.45 MPa,未退火 0.45 MPa, unannealed |
℃ | ISO 75-2/B | |
脆化温度 Embrittlement temperature |
℃ | ISO 974 | |
维卡软化温度 Vicat Softening Temp |
℃ | ISO 306 | |
熔融温度 Melting temperature |
℃ | ISO 11357-3 | |
氧感应时间 Oxygen sensing time |
min | ISO 11357 | |
电气性能 Electrical performance |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
表面电阻率 Surface resistivity |
ohms | IEC 60093 | |
阻燃性能 FLAME CHARACTERISTICS |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
阻燃等级 Flame retardant level |
UL 94 | ||
补充信息 Supplementary information |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
UV Rating UV Rating |
hr | ASTM D2565 | |
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
邵氏硬度 Shore hardness |
|||
邵氏 D Shaw's D |
ISO 868 | ||
拉伸强度 tensile strength |
|||
屈服 yield |
MPa | ISO 527-2 | |
拉伸应变 Tensile strain |
|||
屈服 yield |
% | ISO 527-2 | |
弯曲模量 Bending modulus |
MPa | ISO 178 |
备注 | |||
---|---|---|---|
暂无数据 |
【新闻资讯】查看全部
如何应对注塑机开模震动?
2018-03-28 开锁模是最容易产生震动的,而震动对机器的寿命和稳定性都有较大的影响,所以在调整开锁模时请注意以下事项:慢速开模速度是模具启动的速度,所以速度在中速以下,一般采用慢速中压,因为锁模时模板有一定量的变形来产生锁模力,所以启动压力可以适当大一些,一般在50%左右,慢速位置视机型而定,一般在模具开到一点点的位置时为减少开模时间而转快速开模。 快速开模速度压力可以适当大一些以减少开模时间,但快速开模位置和减速开模位置一定要适当拉开距离,因为快速开模时的冲击和惯性比较大,必须要一段距离 |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |